| Rev |
Log message |
Author |
Age |
Path |
| 204 |
Fixed more incorrect comments |
jshamlet |
1675d 21h |
/ |
| 203 |
Removed an extra delay FF from the bitclock rising edge signal for the clock slave configuration to better center the rising edge pulse on the receive signal. |
jshamlet |
1676d 03h |
/ |
| 202 |
Fixed receiver bug that caused false flag detection,
Split the large sdlc_serial_ctrl entity into sub-entities to make debugging easier. |
jshamlet |
1676d 04h |
/ |
| 201 |
Fixed comments regarding RX Checksum location |
jshamlet |
1678d 01h |
/ |
| 200 |
Renamed dual-port buffer to match other entities. |
jshamlet |
1678d 02h |
/ |
| 199 |
Added monitor ram for debugging and fixed issue with dual-port read path. |
jshamlet |
1678d 02h |
/ |
| 198 |
Removed debugging memory |
jshamlet |
1678d 10h |
/ |
| 197 |
Fixed incorrect comments |
jshamlet |
1678d 10h |
/ |
| 196 |
Modified the update logic to allow direct writes to offset 0xFE for refreshing the clock status. This way, any write to the clock status register will immediately be undone. (Writing 0x00 to offset 0xFF is once-more ignored) |
jshamlet |
1678d 11h |
/ |
| 195 |
Added dual-port RAM core for SDLC interface. |
jshamlet |
1679d 05h |
/ |
| 194 |
Cleaned up licensing sections |
jshamlet |
1679d 05h |
/ |
| 193 |
Fixed incorrect comment in o8_alu16.vhd. The value of the write to 0x1F doesn't matter, as the write itself triggers the calculation. |
jshamlet |
1679d 06h |
/ |
| 192 |
Added SDLC packet engine |
jshamlet |
1679d 06h |
/ |
| 191 |
Cleaned up comments, added back the OPEN8_NULLBUS constant, and added some new modules for ADCs and LCD displays.
Also made the button input module more configurable by moving the debounce code to a separate entity and using generics to instantiate it. |
jshamlet |
1679d 06h |
/ |
| 190 |
Fixed a bug in CPU where RTI/RTS wasn't idling the instruction cache, causing intermittent failures where RTI would execute as RTS, corrupting the stack;
Fixed a bug in the real-time clock where the uSec tick generator would stop if the PIT timer value was left/set to 0x00. |
jshamlet |
1691d 04h |
/ |
| 189 |
Merged changes from private repository,
added ceil_log2 function to Open8_pkg, since it is used to calculate RAM vectors,
cleaned up comments and removed local copies of the ceil_log2 function from peripherals. |
jshamlet |
1692d 04h |
/ |
| 188 |
Added a generic to alter the behavior of RTI so that it can optionally skip restoring the general purpose flags GP4 to GP7, allowing ISR's to make persistent changes to them. Also exported these flags to the top level for use outside the CPU. |
jshamlet |
1692d 07h |
/ |
| 187 |
Added the CPU_Halt input, only now as an input to the instruction decoder. The CPU_Halt line will assert the registered CPU_Halt_Req, which will cause the instruction decoder to abort the current instruction, reset the PC, then enter a hold state until the line is deasserted. Additionally, a very minor bug that could cause the SMSK instruction to effectively execute twice if interrupted was fixed. Lastly, cleaned up the comments even more. |
jshamlet |
1694d 03h |
/ |
| 186 |
Merged the interrupt override logic into the case structure, simplifying how interrupts are processed. |
jshamlet |
1697d 03h |
/ |
| 185 |
1) Fixed an apparently long-standing bug where the interrupt bit wasn't being cleared after an RTI
2) Modified the program counter logic to be simpler. It now always increments, and states control the increment using the offset field. A new set of constants was added to replace the old states.
3) Modified the ALU to always use Operand1 instead of ALU_Ctrl.Data (and removed the field in the record). A new ALU command, ALU_GMSK, was added, as it was the only instruction to set the .Data field to something other than Operand1 (Int_Mask)
4) Modified the package file so that flag names match what the assembler calls them. FL_Z is now PSR_Z, FL_GP1 is now PSR_GP4, etc.
5) Cleaned up the comments and code formatting |
jshamlet |
1697d 06h |
/ |
