OpenCores
URL https://opencores.org/ocsvn/gecko3/gecko3/trunk

Subversion Repositories gecko3

[/] [gecko3/] [trunk/] [GECKO3COM/] [gecko3com-ip/] [core/] [GECKO3COM_simple_test.vhd] - Rev 30

Rev

Details | Compare with Previous | Blame

Filtering Options

Clear current filter

Rev Log message Author Age Path
30 done. nussgipfel 5415d 16h /gecko3/trunk/GECKO3COM/gecko3com-ip/core/GECKO3COM_simple_test.vhd
29 some bugfixes and here and there some comment cleaning nussgipfel 5415d 21h /gecko3/trunk/GECKO3COM/gecko3com-ip/core/GECKO3COM_simple_test.vhd
28 switched to work on the v1 production GECKO3main. the timing is a big issue
with the prototype system. the cabeling and the possibly bad influence of the
prototype board layout makes it impossible to run this core in sync with the
host transfers.

out transfer is fully working. always in sync with the transfers and reads all
tmc headers correctly.

abort handling in the core works as well. there were some fixes needed in the
firmware, not all IN FIFO buffer where flushed.

a lot of work was done for the IN transfer (fpga to pc). the in transfer
handling in GECKO3COM_simple_test.vhd is finished.

the GECKO3COM_simple_datapath/fsm is finished.

there is still an issue left but I think the problem is in the gpif_com
module. for long IN transfers, we still not receive the correct number of bytes.

it works great for all sort of short transfers.


Here I present a time measurement to show the achieved message throughput:
(Response message was 1 byte, total with header and align bytes was 16 byte)

time for i in {0..100000}; do cat /dev/usbtmc1 > /dev/null; done

real 5m45.706s
user 0m27.498s
sys 4m52.676s

This shows that we can read data from the fpga with a rate up to 290 Hz		 nussgipfel 5417d 22h /gecko3/trunk/GECKO3COM/gecko3com-ip/core/GECKO3COM_simple_test.vhd
27 some of the problems are fixed now, some still remain.

all transfersize counter where wrong. they have to count the correct number of bytes transfered.
handling of a "short word" added, to be shure that all data (also when it is shorter than a word)
is transfered.

corrected some errors with the fifo write enable signals.		 nussgipfel 5420d 03h /gecko3/trunk/GECKO3COM/gecko3com-ip/core/GECKO3COM_simple_test.vhd
26 basic in/out transfers working. tester consumes data and generates the test messages.
protocol handling is working. at the moment it gets out of sync for long data outs.
for in transfers, to less data is sent to the host, deadlock for long in transfers.		 nussgipfel 5423d 17h /gecko3/trunk/GECKO3COM/gecko3com-ip/core/GECKO3COM_simple_test.vhd
25 small update in the comments nussgipfel 5428d 23h /gecko3/trunk/GECKO3COM/gecko3com-ip/core/GECKO3COM_simple_test.vhd
24 first version of the GECKO3COM_simple_test that successfully synthesized.
debugging starts now.

fixed a small bug in the gpif_com_test due to the adding of the gpif_com_eom signal and the eom bit
flip-flop in the gpif_com module.		 nussgipfel 5428d 23h /gecko3/trunk/GECKO3COM/gecko3com-ip/core/GECKO3COM_simple_test.vhd
23 GECKO3COM_simple_test designed and written.
added needed switches to the ucf files.

did some cleanup in the GECKO3_simple_*		 nussgipfel 5430d 19h /gecko3/trunk/GECKO3COM/gecko3com-ip/core/GECKO3COM_simple_test.vhd
14 reorganising and renaming the stuff in these project.

the core will get the name "GECKO3COM_" followed by the type "simple", "plb" or "opb"
to follow the naming in the GECKO3 wiki and to show the IP core interface.

duplicated fifo corecenerator files are merged together including a wrapper to easily supress synthesizer warnings
from unavailable, unused and unconnected pins.

the project is now organised in a way how the IP core and it's parts are beeing used. this means that the
low-level gpif access module is instantiated by the higher level modules and not the other way around.
this will make more sense when more parts of this IP core are finished (planning is finished, they have
to be implemented and tested now).		 nussgipfel 5487d 03h /gecko3/trunk/GECKO3COM/gecko3com-ip/core/GECKO3COM_loopback.vhd
12 this is the version 0.4 of the GECKO3com IP core.

This is the last version from Andreas Habegger, the maintainer for this core is now Christoph Zimmermann		 nussgipfel 5502d 06h /gecko3/trunk/GECKO3COM/gecko3com-ip/core/USB_TMC_IP_loopback.vhd
11 initial add of the version 0.3 of the GECKO3com IP core. originaly developped by Andreas Habegger.

this commit is just for backup and to make the project progress visible because version 0.4 is also ready and will be commited in the next step.		 nussgipfel 5502d 06h /gecko3/trunk/GECKO3COM/gecko3com-ip/core/USB_TMC_IP_loopback.vhd

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.