Rev |
Log message |
Author |
Age |
Path |
150 |
Updating installation script to retrieve minsoc from tags/release-1.0. |
rfajardo |
4749d 09h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |
147 |
Updating minsoc_bench.v to correctly acquire uart data.
Uart drivers: when an end of line character was sent, the driver appended a carriage return to it. This is not necessary and has been removed.
-Eth and Uart firmwares also had a carriage return after the end of line, also removed.
Minsoc_bench_defines.v: Renaming VCD_OUTPUT define to WAVEFORM_OUTPUT
run_bench: selecting -lxt2 for waveform output format. This output format size is 10 times smaller than vcd.
minsoc-install.sh: lxt2 output format requires that Icarus Verilog be installed with zlib support. For that, we now check if zlib is supported on script run. |
rfajardo |
4754d 07h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |
138 |
DIR_TO_INSTALL creation using wizard |
ConX. |
4755d 22h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |
136 |
Installation on Ubuntu-11.10 has shown that a binary called makeinfo is required to install GDB. This binary can be installed on Ubuntu by installing the package texinfo. |
rfajardo |
4763d 05h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |
115 |
configure.sh script dir aware.
minsoc-install.sh logging to script dir. |
rfajardo |
4781d 06h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |
114 |
Installation and Configuration scripts can be run out of any directory.
They assume they are going to process the files and directories found in the directory they are run from. |
rfajardo |
4781d 06h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |
113 |
minsoc-install.sh & minsoc-configure.sh:
-aware of location of configure.sh script
configure.sh:
-does not block on patch error
spartan3e_starter_kit & spartan3e_starter_kit_eth:
-or1200_defines.v updated
prj:
-src/blackboxes/or1200_top.v adjusted to or1200_rel1
-Makefile had a typo regarding altera vhdl files |
rfajardo |
4781d 06h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |
112 |
Updating installation & configuration scripts. |
rfajardo |
4781d 21h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |
111 |
minsoc-install.sh: DIR_TO_INSTALL is required before using beautify.sh |
rfajardo |
4781d 22h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |
110 |
Fixing several minor issues with the system:
-minsoc-install splitted into installation and configuration
-minsoc-configure.sh can be used to configure a fresh checked out system
-configure script used by both minsoc-configure.sh and minsoc-install.sh to configure
-rtl/verilog: svn externals fixed
-or1200 rolled back to release-1.0
-prj/scripts:
-Makefile has been used by simulation to differentiate project definition of vhdl and verilog files
-Altera was differentiating it in script
-now there are two scripts, one for vhdl and another for verilog. The differentiation occurs in Makefile as for simulation.
-altera_3c25_board/configure scripts had to be updated, vprj and vhdprj file extensions used to differentiate Verilog and VHDL project files.
-prj/src: or1200_top.prj downdated to definition of or1200_v1 |
rfajardo |
4781d 22h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |
109 |
Creating a branche for release candidate 1.0. |
rfajardo |
4782d 00h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |
106 |
Installation script was checking the ENV variable before setting it. |
rfajardo |
4782d 09h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |
103 |
But the file is called gdb-6.8a.tar.bz2, so tar must be run on that name. |
rfajardo |
4792d 01h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |
102 |
GNU GDB FTP has renamed gdb-6.8 package to gdb-6.8a package. Uncompressed it remains gdb-6.8, so no other changes to script are necessary. |
rfajardo |
4792d 01h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |
83 |
minsoc-install.sh: bzip2 program was being used, but its existance on target system was not being verified. It is now. |
rfajardo |
4844d 10h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |
82 |
minsoc-install.sh: problems with copying the GNU Toolchain from download to tools. We uncompress the GNU Toolchain now once again to tools during the installation part. |
rfajardo |
4847d 10h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |
81 |
Installation script complete, nice text feedback, output logs and better execution order. |
rfajardo |
4847d 21h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |
79 |
minsoc-install.sh: rpath corrected.
required-cygwin-tools: updated |
rfajardo |
4851d 02h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |
78 |
minsoc-install.sh: Advanced JTAG bridge compilation needs to know where the dynamic libraries are on runtime. Patching (sed) the Makefile to compile it with the rpath to the libraries (libusb/libftdi). |
rfajardo |
4851d 02h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |
77 |
New tool requirements for installing Icarus Verilog. |
rfajardo |
4851d 02h |
/minsoc/branches/rc-1.0/utils/setup/minsoc-install.sh |