| Rev |
Log message |
Author |
Age |
Path |
| 140 |
Including required modules for verilator simulation. |
rfajardo |
4778d 23h |
/minsoc/branches/verilator/rtl/verilog/minsoc_top.v |
| 139 |
Creating a verilator branche. |
rfajardo |
4778d 23h |
/minsoc/branches/verilator/rtl/verilog/minsoc_top.v |
| 109 |
Creating a branche for release candidate 1.0. |
rfajardo |
4805d 13h |
/minsoc/branches/verilator/rtl/verilog/minsoc_top.v |
| 75 |
Adapting minsoc_top.v and minsoc_verilog_files.txt to new names for top modules and define file of ethmac ip core. |
rfajardo |
4881d 15h |
/minsoc/branches/verilator/rtl/verilog/minsoc_top.v |
| 60 |
Selection of memory model or implementation memory is now made on minsoc_bench_defines.v. It is done by a definition instead of including different files for simulation.
minsoc_bench_defines.v definition of reset level was not correct. It based the level decision on defineds POSITIVE_RESET or NEGATIVE_RESET, which couldn't be defined by then, since minsoc_defines.v is not included in minsoc_bench_defines.v. The decision has been moved to minsoc_bench.v and made a localparam instead of a definition. |
rfajardo |
4986d 10h |
/minsoc/branches/verilator/rtl/verilog/minsoc_top.v |
| 56 |
Macros for all Altera family devices and pll instantiation |
javieralso |
4993d 10h |
/minsoc/branches/verilator/rtl/verilog/minsoc_top.v |
| 52 |
Altera ALTPLL Megafunction Instantiation |
javieralso |
5003d 12h |
/minsoc/branches/verilator/rtl/verilog/minsoc_top.v |
| 33 |
Start-up Starter, included in the MinSoC top file, has been updated to three-phase instruction output; instruction assertion, acknowledge assertion, and next instruction with acknowledge deassertion.
Previously it was two-phase with next instruction, instruction assertion and acknowledge assertion together, and acknowledge deassertion.
That is required by the new Wishbone master interface used by OpenRISC release 3. |
rfajardo |
5189d 20h |
/minsoc/branches/verilator/rtl/verilog/minsoc_top.v |
| 31 |
Adaption to or1200_r3. It is still important to change or1200_defines.v:
-`define OR1200_BOOT_ADR 32'hf0000100 to `define OR1200_BOOT_ADR 32'h00000100 |
rfajardo |
5259d 01h |
/minsoc/branches/verilator/rtl/verilog/minsoc_top.v |
| 26 |
On version 34 of the Advanced Debug System the signal debug_tdo_o from the altera_virtual_jtag has changed to debug_tdo_i.
This commit adapts minsoc_top.v accordingly. |
rfajardo |
5369d 07h |
/minsoc/branches/verilator/rtl/verilog/minsoc_top.v |
| 20 |
minsoc_defines.v had a semicolon at the end of the two reset polarity definitions.
minsoc_top had a signal array for two different signals which was for backward compatibility. The compatible debugging module is so old that there is no reason for keeping it.
Documentation has been updated to better explain how to use the definitions files, minsoc_defines.v and or1200_defines.v. An example for Altera devices has been added too. |
rfajardo |
5448d 19h |
/minsoc/branches/verilator/rtl/verilog/minsoc_top.v |
| 17 |
Ethernet testbench speed penalty solved. Now Ethernet of testbench and minsoc can be enabled by only uncommenting `define ETHERNET on minsoc_defines.v.
send_mac, get_mac and uart_send tasks have been included/improved. Also a testbench, which works for both included firmwares is added. (eth and uart)
If ETHERNET is defined for the SoC, both firmwares will complete successfully. If not, the eth firmware will stall when trying to access the Ethernet module. |
rfajardo |
5513d 18h |
/minsoc/branches/verilator/rtl/verilog/minsoc_top.v |
| 16 |
Further initialization improvement of non-used signals, setting interrupt signals to 0 if module is not used. |
rfajardo |
5518d 22h |
/minsoc/branches/verilator/rtl/verilog/minsoc_top.v |
| 14 |
Wishbone error signal of Ethernet core was not tied to ground if Ethernet was disabled. Solved now. |
rfajardo |
5527d 23h |
/minsoc/branches/verilator/rtl/verilog/minsoc_top.v |
| 7 |
Some changes:
-wb_cabs removed from minsoc_top.v and minsoc_tc_top.v
-added reset polarity control to minsoc_defines.v through:
-POSITIVE_RESET
-NEGATIVE_RESET
-minsoc_onchip_ram_top.v does not use
minsoc_onchip_ram.v oe signals (output enable) anymore,
which are implemented as tristate buffers. Now
minsoc_onchip_ram_top.v has a generated MUX, which
has an arbitrary number of inputs and 1 output.
Input are the internal output of the onchip_rams,
output the wb_dat_o. |
rfajardo |
5559d 17h |
/minsoc/branches/verilator/rtl/verilog/minsoc_top.v |
| 2 |
First commit of project. Beta status:
-testbench: working
-firmware: working
-RTL: Working for: Xilinx Spartan-3A DSP Development Kit |
rfajardo |
5573d 21h |
/minsoc/branches/verilator/rtl/verilog/minsoc_top.v |
