Rev |
Log message |
Author |
Age |
Path |
43 |
Removed latch on "dbg" signal |
wzab |
2676d 11h |
/fade_ether_protocol/trunk/stable_jumbo_frames_version/ |
42 |
KC705 design upgraded to Vivado 2016.4
Corrrected indentation in a few files in AFCK design |
wzab |
2676d 15h |
/fade_ether_protocol/trunk/stable_jumbo_frames_version/ |
41 |
The AFCK project upgraded to Vivado 2016.4 |
wzab |
2676d 16h |
/fade_ether_protocol/trunk/stable_jumbo_frames_version/ |
40 |
The "jumbo frame version" renamed from "experimental" to "stable". |
wzab |
2676d 21h |
/fade_ether_protocol/trunk/stable_jumbo_frames_version/ |
39 |
Added receiver2t4 - program allowing to receive data from 4 links simultaneously |
wzab |
3245d 10h |
/fade_ether_protocol/trunk/experimental_jumbo_frames_version/ |
38 |
In synthesis scripts added waiting, until bitsream is generated... |
wzab |
3276d 19h |
/fade_ether_protocol/trunk/experimental_jumbo_frames_version/ |
37 |
Added new design for AFCK board, which uses 8 10 Gbps links.
Additionally added I2C control of the AFCK Si57x based clock.
The I2C controller is driven via VIO blocks controlled by JTAG
interface from Vivado Tcl console.
Tcl scripts are in the fpga/src/AFCK/i2c_tools directory.
To configure clock to 156.25MHz, and to route it to links,
change directory to fpga/src/AFCK/i2c_tools and do
"source start_10g_links.tcl".
After the clock is reprogrammed, reconfigure the FPGA again
(it seems, that there is a problem with reseting links after
clock is reconfigured). |
wzab |
3278d 10h |
/fade_ether_protocol/trunk/experimental_jumbo_frames_version/ |
36 |
Added signals needed to ensure, that Si570/1 chip generates the clock.
Added signals driving the rate select lines in the SFP+ modules high.
Added two XDC files - the first one for FM-S14 in the FMC1
connector, the second one for FM-S14 in the FMC2 connector. |
wzab |
3294d 12h |
/fade_ether_protocol/trunk/experimental_jumbo_frames_version/ |
35 |
Changed comment in definition of the descriptor record
Updated IP cores in project for KC705 (to Vivado 2014.4) |
wzab |
3397d 12h |
/fade_ether_protocol/trunk/experimental_jumbo_frames_version/ |
33 |
Added script for automatic compilation of FADE for AFCK, using Vivado 2014.4 |
wzab |
3413d 22h |
/fade_ether_protocol/trunk/experimental_jumbo_frames_version/ |
32 |
Added the 4-channel FADE test implementation for the AFCK board. |
wzab |
3414d 02h |
/fade_ether_protocol/trunk/experimental_jumbo_frames_version/ |
31 |
Added receiver2t_cmd to the Makefile |
wzab |
3418d 15h |
/fade_ether_protocol/trunk/experimental_jumbo_frames_version/ |
30 |
Corrected error which slows down handling of user commands (the thread
executing the user command used wait_event_timeout instead of
wait_event_timeout_interruptiple).
Added demo program which tests time of execution of the user's
command. |
wzab |
3418d 16h |
/fade_ether_protocol/trunk/experimental_jumbo_frames_version/ |
29 |
Fixed two mistakes in mutex management (mutex not unlocked, when function leaved after an error)
Fixed dead URL in comments. |
wzab |
3423d 17h |
/fade_ether_protocol/trunk/experimental_jumbo_frames_version/ |
28 |
Correction of an obvious mistake in the Linux driver, which lead to deadlock
when two applications (or two threads) tried to open the same FADE device. |
wzab |
3427d 15h |
/fade_ether_protocol/trunk/experimental_jumbo_frames_version/ |
27 |
Added file fade_one_channel, allowing to implement multiple FADE instances in a single FPGA. |
wzab |
3442d 00h |
/fade_ether_protocol/trunk/experimental_jumbo_frames_version/ |
26 |
Corrected small bug in CRC update in eth_sender8,vhd
Added counter of retransmitted packets.
Some minor changes in delay update parameters. |
wzab |
3476d 10h |
/fade_ether_protocol/trunk/experimental_jumbo_frames_version/ |
25 |
Modified the Tcl script for KC705 so, that it automatically runs synthesis, implementation and generates bitstream. |
wzab |
3500d 01h |
/fade_ether_protocol/trunk/experimental_jumbo_frames_version/ |
24 |
Added build scripts for KC705 (somehow they got omitted in version 22) |
wzab |
3500d 14h |
/fade_ether_protocol/trunk/experimental_jumbo_frames_version/ |
23 |
Added script allowing for batch compilation of FADE 10G for Atlys.
Just run build_proj_atlys.sh
Removed compilation of receiver2.c (which has been deleted) in the Makefile.
Slightly changed order of operation in the receiver2t.c |
wzab |
3500d 14h |
/fade_ether_protocol/trunk/experimental_jumbo_frames_version/ |