Rev |
Log message |
Author |
Age |
Path |
165 |
Board contribution: nexys2_1200 (Thanks to Johan Granath)
spartan3e_starter_kit_eth/minsoc_bench_defines.v: deprecated definition updated |
rfajardo |
4697d 09h |
/ |
164 |
Updating width of minsoc_tc_top.v for Wishbone B3 compliance. This file has never worked. This solves at least the bug that some signals were not being routed through. |
rfajardo |
4762d 01h |
/ |
163 |
Adjusting internal initiator array widths. They were 1 bit too large. Thanks to R. Diez report.
These arrays abstract the complete initiator inputs. This way it is easier to route and arbiter using a single input.
Also removing 2 sequential delays. I didn't design them, so I can't tell if they were really useful/good. |
rfajardo |
4768d 08h |
/ |
162 |
Tasks don't have parenthesis. This is only used for ports on modules. This was a mistake from my part. |
rfajardo |
4774d 03h |
/ |
161 |
Correcting configure parameters of adv_jtag_bridge on installation script. |
rfajardo |
4787d 06h |
/ |
160 |
Typo in minsoc-install.sh script. Adv_jtag_bridge was not configuring correctly. |
rfajardo |
4787d 06h |
/ |
159 |
Updated constraint file for de2_115 board. (Richard Hasha) |
rfajardo |
4787d 07h |
/ |
158 |
Adding de2_115_board port, thanks to Richard Hasha.
Support to JSP (JTAG Serial Port) working well. Also provided by Richard Hasha.
Different interconnect configurations per board are not straightforward on MinSoC. New added modules or definitions for addresses have to be carried over to other boards. Furthermore, extra modules can be shared among all projects. Thus, it is better to have this centralized:
-Removing interconnect configuration from minsoc_defines.v. There is an interconnect_defines.v file on rtl/verilog. The software counterpart is interconnect.h on sw/drivers.
Including a jsp firmware. It is basically the uart firmware but using JSP instead. Added to all board configure scripts to be compiled on configuration.
prj/srcs extended to include jsp and interconnec_defines.v.
spartan3e_starter_kit_eth lost UART (does not fit) and uses JSP instead now. |
rfajardo |
4788d 23h |
/ |
157 |
Removed obsolete file; the changes in this version have been merged into
the mainline advanced debug system version 3.0 and higher. |
nyawn |
4794d 18h |
/ |
156 |
Added hardware watchpoint indicators to debug unit break input, to allow
the debugger to break when a hardware watchpoint is triggered. |
nyawn |
4794d 18h |
/ |
155 |
Decreased wait time, for faster simulations. |
nyawn |
4794d 18h |
/ |
154 |
Modified to use the new autotools support in the advanced debug system v3.0. |
nyawn |
4794d 18h |
/ |
153 |
Updating installation script to download minsoc from this branche, verilator, instead of rc-1.0. |
rfajardo |
4827d 07h |
/ |
152 |
Roll back to retrieve minsoc from branches/rc-1.0. |
rfajardo |
4827d 07h |
/ |
151 |
Creating tag release-1.0 from revision 150 of branches/rc-1.0. |
rfajardo |
4827d 07h |
/ |
150 |
Updating installation script to retrieve minsoc from tags/release-1.0. |
rfajardo |
4827d 07h |
/ |
149 |
Merging differences of release candidate 1.0 revision 140:148 with trunk. |
rfajardo |
4827d 08h |
/ |
148 |
Renaming minsoc_wave.lxt to minsoc_wave.lxt2 for correctness. |
rfajardo |
4832d 04h |
/ |
147 |
Updating minsoc_bench.v to correctly acquire uart data.
Uart drivers: when an end of line character was sent, the driver appended a carriage return to it. This is not necessary and has been removed.
-Eth and Uart firmwares also had a carriage return after the end of line, also removed.
Minsoc_bench_defines.v: Renaming VCD_OUTPUT define to WAVEFORM_OUTPUT
run_bench: selecting -lxt2 for waveform output format. This output format size is 10 times smaller than vcd.
minsoc-install.sh: lxt2 output format requires that Icarus Verilog be installed with zlib support. For that, we now check if zlib is supported on script run. |
rfajardo |
4832d 06h |
/ |
146 |
Importing 'Xilinx Microblaze Dev. Kit 1600E Edition' board configuration directory. |
ConX. |
4832d 12h |
/ |
145 |
minsoc_bench_core.v and minsoc_bench_clock.v left only on verilator branche. It will develop there until it is ported for inclusion into trunk. RC-1.0 is now clean of it. |
rfajardo |
4832d 21h |
/ |
144 |
Updating configure scripts. Calling make into the right directories now. |
rfajardo |
4833d 07h |
/ |
143 |
Compiling firmwares in board configuration scripts instead of on global minsoc setup. |
rfajardo |
4833d 07h |
/ |
142 |
Updating configure.sh:
1) we don't patch the trunk version.
2) it is better to re-compile the firmwares on reconfiguration. So compiling firmwares went to configure scripts instead.
backend/xxx/configure: compiling firmwares here now. |
rfajardo |
4833d 07h |
/ |
141 |
Merging with rc-1.0 revision 140. I doubt rc-1.0 will still change much in the last days. |
rfajardo |
4833d 07h |
/ |
140 |
Including required modules for verilator simulation. |
rfajardo |
4833d 08h |
/ |
139 |
Creating a verilator branche. |
rfajardo |
4833d 08h |
/ |
138 |
DIR_TO_INSTALL creation using wizard |
ConX. |
4833d 21h |
/ |
137 |
Removing uncomplete support for ml509 and not working support for spartan3e_starter_kit_eth (area constraint cannot be reached). |
rfajardo |
4834d 07h |
/ |
136 |
Installation on Ubuntu-11.10 has shown that a binary called makeinfo is required to install GDB. This binary can be installed on Ubuntu by installing the package texinfo. |
rfajardo |
4841d 03h |
/ |