Rev |
Log message |
Author |
Age |
Path |
158 |
Adding de2_115_board port, thanks to Richard Hasha.
Support to JSP (JTAG Serial Port) working well. Also provided by Richard Hasha.
Different interconnect configurations per board are not straightforward on MinSoC. New added modules or definitions for addresses have to be carried over to other boards. Furthermore, extra modules can be shared among all projects. Thus, it is better to have this centralized:
-Removing interconnect configuration from minsoc_defines.v. There is an interconnect_defines.v file on rtl/verilog. The software counterpart is interconnect.h on sw/drivers.
Including a jsp firmware. It is basically the uart firmware but using JSP instead. Added to all board configure scripts to be compiled on configuration.
prj/srcs extended to include jsp and interconnec_defines.v.
spartan3e_starter_kit_eth lost UART (does not fit) and uses JSP instead now. |
rfajardo |
4500d 16h |
/minsoc |
157 |
Removed obsolete file; the changes in this version have been merged into
the mainline advanced debug system version 3.0 and higher. |
nyawn |
4506d 11h |
/minsoc |
156 |
Added hardware watchpoint indicators to debug unit break input, to allow
the debugger to break when a hardware watchpoint is triggered. |
nyawn |
4506d 11h |
/minsoc |
155 |
Decreased wait time, for faster simulations. |
nyawn |
4506d 11h |
/minsoc |
154 |
Modified to use the new autotools support in the advanced debug system v3.0. |
nyawn |
4506d 11h |
/minsoc |
153 |
Updating installation script to download minsoc from this branche, verilator, instead of rc-1.0. |
rfajardo |
4539d 01h |
/minsoc |
152 |
Roll back to retrieve minsoc from branches/rc-1.0. |
rfajardo |
4539d 01h |
/minsoc |
151 |
Creating tag release-1.0 from revision 150 of branches/rc-1.0. |
rfajardo |
4539d 01h |
/minsoc |
150 |
Updating installation script to retrieve minsoc from tags/release-1.0. |
rfajardo |
4539d 01h |
/minsoc |
149 |
Merging differences of release candidate 1.0 revision 140:148 with trunk. |
rfajardo |
4539d 02h |
/minsoc |
148 |
Renaming minsoc_wave.lxt to minsoc_wave.lxt2 for correctness. |
rfajardo |
4543d 22h |
/minsoc |
147 |
Updating minsoc_bench.v to correctly acquire uart data.
Uart drivers: when an end of line character was sent, the driver appended a carriage return to it. This is not necessary and has been removed.
-Eth and Uart firmwares also had a carriage return after the end of line, also removed.
Minsoc_bench_defines.v: Renaming VCD_OUTPUT define to WAVEFORM_OUTPUT
run_bench: selecting -lxt2 for waveform output format. This output format size is 10 times smaller than vcd.
minsoc-install.sh: lxt2 output format requires that Icarus Verilog be installed with zlib support. For that, we now check if zlib is supported on script run. |
rfajardo |
4543d 23h |
/minsoc |
146 |
Importing 'Xilinx Microblaze Dev. Kit 1600E Edition' board configuration directory. |
ConX. |
4544d 05h |
/minsoc |
145 |
minsoc_bench_core.v and minsoc_bench_clock.v left only on verilator branche. It will develop there until it is ported for inclusion into trunk. RC-1.0 is now clean of it. |
rfajardo |
4544d 14h |
/minsoc |
144 |
Updating configure scripts. Calling make into the right directories now. |
rfajardo |
4545d 01h |
/minsoc |
143 |
Compiling firmwares in board configuration scripts instead of on global minsoc setup. |
rfajardo |
4545d 01h |
/minsoc |
142 |
Updating configure.sh:
1) we don't patch the trunk version.
2) it is better to re-compile the firmwares on reconfiguration. So compiling firmwares went to configure scripts instead.
backend/xxx/configure: compiling firmwares here now. |
rfajardo |
4545d 01h |
/minsoc |
141 |
Merging with rc-1.0 revision 140. I doubt rc-1.0 will still change much in the last days. |
rfajardo |
4545d 01h |
/minsoc |
140 |
Including required modules for verilator simulation. |
rfajardo |
4545d 01h |
/minsoc |
139 |
Creating a verilator branche. |
rfajardo |
4545d 01h |
/minsoc |
138 |
DIR_TO_INSTALL creation using wizard |
ConX. |
4545d 14h |
/minsoc |
137 |
Removing uncomplete support for ml509 and not working support for spartan3e_starter_kit_eth (area constraint cannot be reached). |
rfajardo |
4546d 01h |
/minsoc |
136 |
Installation on Ubuntu-11.10 has shown that a binary called makeinfo is required to install GDB. This binary can be installed on Ubuntu by installing the package texinfo. |
rfajardo |
4552d 20h |
/minsoc |
135 |
Installation on Ubuntu-11.10 has shown that package texinfo is required to compiled GDB. This package installs the binary makeinfo. |
rfajardo |
4552d 20h |
/minsoc |
134 |
run_sim.bat for ModelSim updated to acquire the firmware_size for command line input when running the testbench. |
rfajardo |
4560d 00h |
/minsoc |
133 |
Roll back minsoc_bench.v to timed simulation. Merge minsoc_bench_core and minsoc_bench_clock again.
Applying Rubén Diez patch to avoid warnings on firmware load for simulation. |
rfajardo |
4560d 02h |
/minsoc |
132 |
ModelSim simulation, running top_module minsoc_bench_clock now, instead of minsoc_bench. |
rfajardo |
4563d 21h |
/minsoc |
131 |
Renaming testbench modules. Adding to ifdefs without which the testbench generation can fail. |
rfajardo |
4563d 22h |
/minsoc |
130 |
minsoc_bench.v: task test_eth has to be phased out together with the ETHERNET definition. If there is no ETHERNET, test_eth cannot be defined. |
rfajardo |
4564d 00h |
/minsoc |
129 |
Removing bugs introduced when splitting clocks and reset.
1) NEGATIVE_RESET or POSITIVE_RESET were missing as definition on minsoc_bench_clock.v (include minsoc_defines.v).
2) wait for reset on minsoc_bench.v to assert design_ready |
rfajardo |
4564d 11h |
/minsoc |