Rev |
Log message |
Author |
Age |
Path |
162 |
Tasks don't have parenthesis. This is only used for ports on modules. This was a mistake from my part. |
rfajardo |
4479d 12h |
/minsoc/ |
161 |
Correcting configure parameters of adv_jtag_bridge on installation script. |
rfajardo |
4492d 14h |
/minsoc/ |
160 |
Typo in minsoc-install.sh script. Adv_jtag_bridge was not configuring correctly. |
rfajardo |
4492d 15h |
/minsoc/ |
159 |
Updated constraint file for de2_115 board. (Richard Hasha) |
rfajardo |
4492d 15h |
/minsoc/ |
158 |
Adding de2_115_board port, thanks to Richard Hasha.
Support to JSP (JTAG Serial Port) working well. Also provided by Richard Hasha.
Different interconnect configurations per board are not straightforward on MinSoC. New added modules or definitions for addresses have to be carried over to other boards. Furthermore, extra modules can be shared among all projects. Thus, it is better to have this centralized:
-Removing interconnect configuration from minsoc_defines.v. There is an interconnect_defines.v file on rtl/verilog. The software counterpart is interconnect.h on sw/drivers.
Including a jsp firmware. It is basically the uart firmware but using JSP instead. Added to all board configure scripts to be compiled on configuration.
prj/srcs extended to include jsp and interconnec_defines.v.
spartan3e_starter_kit_eth lost UART (does not fit) and uses JSP instead now. |
rfajardo |
4494d 07h |
/minsoc/ |
157 |
Removed obsolete file; the changes in this version have been merged into
the mainline advanced debug system version 3.0 and higher. |
nyawn |
4500d 02h |
/minsoc/ |
156 |
Added hardware watchpoint indicators to debug unit break input, to allow
the debugger to break when a hardware watchpoint is triggered. |
nyawn |
4500d 02h |
/minsoc/ |
155 |
Decreased wait time, for faster simulations. |
nyawn |
4500d 02h |
/minsoc/ |
154 |
Modified to use the new autotools support in the advanced debug system v3.0. |
nyawn |
4500d 02h |
/minsoc/ |
153 |
Updating installation script to download minsoc from this branche, verilator, instead of rc-1.0. |
rfajardo |
4532d 16h |
/minsoc/ |
152 |
Roll back to retrieve minsoc from branches/rc-1.0. |
rfajardo |
4532d 16h |
/minsoc/ |
151 |
Creating tag release-1.0 from revision 150 of branches/rc-1.0. |
rfajardo |
4532d 16h |
/minsoc/ |
150 |
Updating installation script to retrieve minsoc from tags/release-1.0. |
rfajardo |
4532d 16h |
/minsoc/ |
149 |
Merging differences of release candidate 1.0 revision 140:148 with trunk. |
rfajardo |
4532d 17h |
/minsoc/ |
148 |
Renaming minsoc_wave.lxt to minsoc_wave.lxt2 for correctness. |
rfajardo |
4537d 13h |
/minsoc/ |
147 |
Updating minsoc_bench.v to correctly acquire uart data.
Uart drivers: when an end of line character was sent, the driver appended a carriage return to it. This is not necessary and has been removed.
-Eth and Uart firmwares also had a carriage return after the end of line, also removed.
Minsoc_bench_defines.v: Renaming VCD_OUTPUT define to WAVEFORM_OUTPUT
run_bench: selecting -lxt2 for waveform output format. This output format size is 10 times smaller than vcd.
minsoc-install.sh: lxt2 output format requires that Icarus Verilog be installed with zlib support. For that, we now check if zlib is supported on script run. |
rfajardo |
4537d 14h |
/minsoc/ |
146 |
Importing 'Xilinx Microblaze Dev. Kit 1600E Edition' board configuration directory. |
ConX. |
4537d 20h |
/minsoc/ |
145 |
minsoc_bench_core.v and minsoc_bench_clock.v left only on verilator branche. It will develop there until it is ported for inclusion into trunk. RC-1.0 is now clean of it. |
rfajardo |
4538d 05h |
/minsoc/ |
144 |
Updating configure scripts. Calling make into the right directories now. |
rfajardo |
4538d 16h |
/minsoc/ |
143 |
Compiling firmwares in board configuration scripts instead of on global minsoc setup. |
rfajardo |
4538d 16h |
/minsoc/ |
142 |
Updating configure.sh:
1) we don't patch the trunk version.
2) it is better to re-compile the firmwares on reconfiguration. So compiling firmwares went to configure scripts instead.
backend/xxx/configure: compiling firmwares here now. |
rfajardo |
4538d 16h |
/minsoc/ |
141 |
Merging with rc-1.0 revision 140. I doubt rc-1.0 will still change much in the last days. |
rfajardo |
4538d 16h |
/minsoc/ |
140 |
Including required modules for verilator simulation. |
rfajardo |
4538d 17h |
/minsoc/ |
139 |
Creating a verilator branche. |
rfajardo |
4538d 17h |
/minsoc/ |
138 |
DIR_TO_INSTALL creation using wizard |
ConX. |
4539d 05h |
/minsoc/ |
137 |
Removing uncomplete support for ml509 and not working support for spartan3e_starter_kit_eth (area constraint cannot be reached). |
rfajardo |
4539d 16h |
/minsoc/ |
136 |
Installation on Ubuntu-11.10 has shown that a binary called makeinfo is required to install GDB. This binary can be installed on Ubuntu by installing the package texinfo. |
rfajardo |
4546d 12h |
/minsoc/ |
135 |
Installation on Ubuntu-11.10 has shown that package texinfo is required to compiled GDB. This package installs the binary makeinfo. |
rfajardo |
4546d 12h |
/minsoc/ |
134 |
run_sim.bat for ModelSim updated to acquire the firmware_size for command line input when running the testbench. |
rfajardo |
4553d 16h |
/minsoc/ |
133 |
Roll back minsoc_bench.v to timed simulation. Merge minsoc_bench_core and minsoc_bench_clock again.
Applying Rubén Diez patch to avoid warnings on firmware load for simulation. |
rfajardo |
4553d 17h |
/minsoc/ |