OpenCores
URL https://opencores.org/ocsvn/minsoc/minsoc/trunk

Subversion Repositories minsoc

[/] [minsoc/] - Rev 166

Rev

Go to most recent revision

Filtering Options

Clear current filter

Rev Log message Author Age Path
166 Turning on warnings for genera_bench.

Updating minsoc-install.sh to work better with directories and working around a missing inclusion of libftdi autotools. http://opencores.org/forum,OpenRISC,0,4685,1
rfajardo 2737d 04h /minsoc/
165 Board contribution: nexys2_1200 (Thanks to Johan Granath)

spartan3e_starter_kit_eth/minsoc_bench_defines.v: deprecated definition updated
rfajardo 2754d 05h /minsoc/
164 Updating width of minsoc_tc_top.v for Wishbone B3 compliance. This file has never worked. This solves at least the bug that some signals were not being routed through. rfajardo 2818d 21h /minsoc/
163 Adjusting internal initiator array widths. They were 1 bit too large. Thanks to R. Diez report.

These arrays abstract the complete initiator inputs. This way it is easier to route and arbiter using a single input.

Also removing 2 sequential delays. I didn't design them, so I can't tell if they were really useful/good.
rfajardo 2825d 04h /minsoc/
162 Tasks don't have parenthesis. This is only used for ports on modules. This was a mistake from my part. rfajardo 2830d 23h /minsoc/
161 Correcting configure parameters of adv_jtag_bridge on installation script. rfajardo 2844d 02h /minsoc/
160 Typo in minsoc-install.sh script. Adv_jtag_bridge was not configuring correctly. rfajardo 2844d 02h /minsoc/
159 Updated constraint file for de2_115 board. (Richard Hasha) rfajardo 2844d 03h /minsoc/
158 Adding de2_115_board port, thanks to Richard Hasha.

Support to JSP (JTAG Serial Port) working well. Also provided by Richard Hasha.

Different interconnect configurations per board are not straightforward on MinSoC. New added modules or definitions for addresses have to be carried over to other boards. Furthermore, extra modules can be shared among all projects. Thus, it is better to have this centralized:
-Removing interconnect configuration from minsoc_defines.v. There is an interconnect_defines.v file on rtl/verilog. The software counterpart is interconnect.h on sw/drivers.

Including a jsp firmware. It is basically the uart firmware but using JSP instead. Added to all board configure scripts to be compiled on configuration.

prj/srcs extended to include jsp and interconnec_defines.v.

spartan3e_starter_kit_eth lost UART (does not fit) and uses JSP instead now.
rfajardo 2845d 19h /minsoc/
157 Removed obsolete file; the changes in this version have been merged into
the mainline advanced debug system version 3.0 and higher.
nyawn 2851d 14h /minsoc/
156 Added hardware watchpoint indicators to debug unit break input, to allow
the debugger to break when a hardware watchpoint is triggered.
nyawn 2851d 14h /minsoc/
155 Decreased wait time, for faster simulations. nyawn 2851d 14h /minsoc/
154 Modified to use the new autotools support in the advanced debug system v3.0. nyawn 2851d 14h /minsoc/
153 Updating installation script to download minsoc from this branche, verilator, instead of rc-1.0. rfajardo 2884d 03h /minsoc/
152 Roll back to retrieve minsoc from branches/rc-1.0. rfajardo 2884d 04h /minsoc/
151 Creating tag release-1.0 from revision 150 of branches/rc-1.0. rfajardo 2884d 04h /minsoc/
150 Updating installation script to retrieve minsoc from tags/release-1.0. rfajardo 2884d 04h /minsoc/
149 Merging differences of release candidate 1.0 revision 140:148 with trunk. rfajardo 2884d 04h /minsoc/
148 Renaming minsoc_wave.lxt to minsoc_wave.lxt2 for correctness. rfajardo 2889d 00h /minsoc/
147 Updating minsoc_bench.v to correctly acquire uart data.

Uart drivers: when an end of line character was sent, the driver appended a carriage return to it. This is not necessary and has been removed.
-Eth and Uart firmwares also had a carriage return after the end of line, also removed.

Minsoc_bench_defines.v: Renaming VCD_OUTPUT define to WAVEFORM_OUTPUT

run_bench: selecting -lxt2 for waveform output format. This output format size is 10 times smaller than vcd.

minsoc-install.sh: lxt2 output format requires that Icarus Verilog be installed with zlib support. For that, we now check if zlib is supported on script run.
rfajardo 2889d 02h /minsoc/

1 2 Next >

Show All

powered by: WebSVN 2.1.0

© copyright 1999-2019 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.