OpenCores
URL https://opencores.org/ocsvn/minsoc/minsoc/trunk

Subversion Repositories minsoc

[/] [minsoc/] [branches/] - Rev 158

Rev

Go to most recent revision

Filtering Options

Clear current filter

Rev Log message Author Age Path
153 Updating installation script to download minsoc from this branche, verilator, instead of rc-1.0. rfajardo 2914d 18h /minsoc/branches/
152 Roll back to retrieve minsoc from branches/rc-1.0. rfajardo 2914d 19h /minsoc/branches/
150 Updating installation script to retrieve minsoc from tags/release-1.0. rfajardo 2914d 19h /minsoc/branches/
148 Renaming minsoc_wave.lxt to minsoc_wave.lxt2 for correctness. rfajardo 2919d 15h /minsoc/branches/
147 Updating minsoc_bench.v to correctly acquire uart data.

Uart drivers: when an end of line character was sent, the driver appended a carriage return to it. This is not necessary and has been removed.
-Eth and Uart firmwares also had a carriage return after the end of line, also removed.

Minsoc_bench_defines.v: Renaming VCD_OUTPUT define to WAVEFORM_OUTPUT

run_bench: selecting -lxt2 for waveform output format. This output format size is 10 times smaller than vcd.

minsoc-install.sh: lxt2 output format requires that Icarus Verilog be installed with zlib support. For that, we now check if zlib is supported on script run.
rfajardo 2919d 17h /minsoc/branches/
146 Importing 'Xilinx Microblaze Dev. Kit 1600E Edition' board configuration directory. ConX. 2919d 23h /minsoc/branches/
145 minsoc_bench_core.v and minsoc_bench_clock.v left only on verilator branche. It will develop there until it is ported for inclusion into trunk. RC-1.0 is now clean of it. rfajardo 2920d 08h /minsoc/branches/
143 Compiling firmwares in board configuration scripts instead of on global minsoc setup. rfajardo 2920d 18h /minsoc/branches/
140 Including required modules for verilator simulation. rfajardo 2920d 19h /minsoc/branches/
139 Creating a verilator branche. rfajardo 2920d 19h /minsoc/branches/
138 DIR_TO_INSTALL creation using wizard ConX. 2921d 08h /minsoc/branches/
137 Removing uncomplete support for ml509 and not working support for spartan3e_starter_kit_eth (area constraint cannot be reached). rfajardo 2921d 19h /minsoc/branches/
136 Installation on Ubuntu-11.10 has shown that a binary called makeinfo is required to install GDB. This binary can be installed on Ubuntu by installing the package texinfo. rfajardo 2928d 14h /minsoc/branches/
134 run_sim.bat for ModelSim updated to acquire the firmware_size for command line input when running the testbench. rfajardo 2935d 18h /minsoc/branches/
133 Roll back minsoc_bench.v to timed simulation. Merge minsoc_bench_core and minsoc_bench_clock again.

Applying Rubén Diez patch to avoid warnings on firmware load for simulation.
rfajardo 2935d 20h /minsoc/branches/
132 ModelSim simulation, running top_module minsoc_bench_clock now, instead of minsoc_bench. rfajardo 2939d 15h /minsoc/branches/
131 Renaming testbench modules. Adding to ifdefs without which the testbench generation can fail. rfajardo 2939d 15h /minsoc/branches/
130 minsoc_bench.v: task test_eth has to be phased out together with the ETHERNET definition. If there is no ETHERNET, test_eth cannot be defined. rfajardo 2939d 18h /minsoc/branches/
129 Removing bugs introduced when splitting clocks and reset.
1) NEGATIVE_RESET or POSITIVE_RESET were missing as definition on minsoc_bench_clock.v (include minsoc_defines.v).
2) wait for reset on minsoc_bench.v to assert design_ready
rfajardo 2940d 05h /minsoc/branches/
128 Outsourcing clocks and reset generations from minsoc_bench.v to minsoc_bench_clock.v. rfajardo 2940d 06h /minsoc/branches/

1 2 Next >

Show All

powered by: WebSVN 2.1.0

© copyright 1999-2019 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.