OpenCores
URL https://opencores.org/ocsvn/minsoc/minsoc/trunk

Subversion Repositories minsoc

[/] [minsoc/] [tags/] [release-1.0] - Rev 151

Rev

Go to most recent revision | Details | Compare with Previous | Blame

Filtering Options

Clear current filter

Rev Log message Author Age Path
151 Creating tag release-1.0 from revision 150 of branches/rc-1.0. rfajardo 2931d 15h /minsoc/tags/release-1.0
150 Updating installation script to retrieve minsoc from tags/release-1.0. rfajardo 2931d 15h /minsoc/branches/rc-1.0
148 Renaming minsoc_wave.lxt to minsoc_wave.lxt2 for correctness. rfajardo 2936d 12h /minsoc/branches/rc-1.0
147 Updating minsoc_bench.v to correctly acquire uart data.

Uart drivers: when an end of line character was sent, the driver appended a carriage return to it. This is not necessary and has been removed.
-Eth and Uart firmwares also had a carriage return after the end of line, also removed.

Minsoc_bench_defines.v: Renaming VCD_OUTPUT define to WAVEFORM_OUTPUT

run_bench: selecting -lxt2 for waveform output format. This output format size is 10 times smaller than vcd.

minsoc-install.sh: lxt2 output format requires that Icarus Verilog be installed with zlib support. For that, we now check if zlib is supported on script run.
rfajardo 2936d 14h /minsoc/branches/rc-1.0
146 Importing 'Xilinx Microblaze Dev. Kit 1600E Edition' board configuration directory. ConX. 2936d 20h /minsoc/branches/rc-1.0
145 minsoc_bench_core.v and minsoc_bench_clock.v left only on verilator branche. It will develop there until it is ported for inclusion into trunk. RC-1.0 is now clean of it. rfajardo 2937d 05h /minsoc/branches/rc-1.0
143 Compiling firmwares in board configuration scripts instead of on global minsoc setup. rfajardo 2937d 15h /minsoc/branches/rc-1.0
138 DIR_TO_INSTALL creation using wizard ConX. 2938d 04h /minsoc/branches/rc-1.0
137 Removing uncomplete support for ml509 and not working support for spartan3e_starter_kit_eth (area constraint cannot be reached). rfajardo 2938d 15h /minsoc/branches/rc-1.0
136 Installation on Ubuntu-11.10 has shown that a binary called makeinfo is required to install GDB. This binary can be installed on Ubuntu by installing the package texinfo. rfajardo 2945d 11h /minsoc/branches/rc-1.0
134 run_sim.bat for ModelSim updated to acquire the firmware_size for command line input when running the testbench. rfajardo 2952d 15h /minsoc/branches/rc-1.0
133 Roll back minsoc_bench.v to timed simulation. Merge minsoc_bench_core and minsoc_bench_clock again.

Applying Rubén Diez patch to avoid warnings on firmware load for simulation.
rfajardo 2952d 16h /minsoc/branches/rc-1.0
132 ModelSim simulation, running top_module minsoc_bench_clock now, instead of minsoc_bench. rfajardo 2956d 12h /minsoc/branches/rc-1.0
131 Renaming testbench modules. Adding to ifdefs without which the testbench generation can fail. rfajardo 2956d 12h /minsoc/branches/rc-1.0
130 minsoc_bench.v: task test_eth has to be phased out together with the ETHERNET definition. If there is no ETHERNET, test_eth cannot be defined. rfajardo 2956d 14h /minsoc/branches/rc-1.0
129 Removing bugs introduced when splitting clocks and reset.
1) NEGATIVE_RESET or POSITIVE_RESET were missing as definition on minsoc_bench_clock.v (include minsoc_defines.v).
2) wait for reset on minsoc_bench.v to assert design_ready
rfajardo 2957d 02h /minsoc/branches/rc-1.0
128 Outsourcing clocks and reset generations from minsoc_bench.v to minsoc_bench_clock.v. rfajardo 2957d 02h /minsoc/branches/rc-1.0
127 Removing redundant simulation output. rfajardo 2957d 08h /minsoc/branches/rc-1.0
126 Updating information about simulation time for Ethernet test. rfajardo 2957d 09h /minsoc/branches/rc-1.0
125 Adjusting testbench messages. Creating tasks for firmware tests. rfajardo 2957d 09h /minsoc/branches/rc-1.0

1 2 Next >

Show All

powered by: WebSVN 2.1.0

© copyright 1999-2019 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.