| Rev |
Log message |
Author |
Age |
Path |
| 160 |
Typo in minsoc-install.sh script. Adv_jtag_bridge was not configuring correctly. |
rfajardo |
4486d 14h |
/minsoc/trunk/ |
| 159 |
Updated constraint file for de2_115 board. (Richard Hasha) |
rfajardo |
4486d 14h |
/minsoc/trunk/ |
| 158 |
Adding de2_115_board port, thanks to Richard Hasha.
Support to JSP (JTAG Serial Port) working well. Also provided by Richard Hasha.
Different interconnect configurations per board are not straightforward on MinSoC. New added modules or definitions for addresses have to be carried over to other boards. Furthermore, extra modules can be shared among all projects. Thus, it is better to have this centralized:
-Removing interconnect configuration from minsoc_defines.v. There is an interconnect_defines.v file on rtl/verilog. The software counterpart is interconnect.h on sw/drivers.
Including a jsp firmware. It is basically the uart firmware but using JSP instead. Added to all board configure scripts to be compiled on configuration.
prj/srcs extended to include jsp and interconnec_defines.v.
spartan3e_starter_kit_eth lost UART (does not fit) and uses JSP instead now. |
rfajardo |
4488d 06h |
/minsoc/trunk/ |
| 157 |
Removed obsolete file; the changes in this version have been merged into
the mainline advanced debug system version 3.0 and higher. |
nyawn |
4494d 01h |
/minsoc/trunk/ |
| 156 |
Added hardware watchpoint indicators to debug unit break input, to allow
the debugger to break when a hardware watchpoint is triggered. |
nyawn |
4494d 01h |
/minsoc/trunk/ |
| 155 |
Decreased wait time, for faster simulations. |
nyawn |
4494d 01h |
/minsoc/trunk/ |
| 154 |
Modified to use the new autotools support in the advanced debug system v3.0. |
nyawn |
4494d 01h |
/minsoc/trunk/ |
| 149 |
Merging differences of release candidate 1.0 revision 140:148 with trunk. |
rfajardo |
4526d 16h |
/minsoc/trunk/ |
| 144 |
Updating configure scripts. Calling make into the right directories now. |
rfajardo |
4532d 15h |
/minsoc/trunk/ |
| 142 |
Updating configure.sh:
1) we don't patch the trunk version.
2) it is better to re-compile the firmwares on reconfiguration. So compiling firmwares went to configure scripts instead.
backend/xxx/configure: compiling firmwares here now. |
rfajardo |
4532d 15h |
/minsoc/trunk/ |
| 141 |
Merging with rc-1.0 revision 140. I doubt rc-1.0 will still change much in the last days. |
rfajardo |
4532d 15h |
/minsoc/trunk/ |
| 135 |
Installation on Ubuntu-11.10 has shown that package texinfo is required to compiled GDB. This package installs the binary makeinfo. |
rfajardo |
4540d 11h |
/minsoc/trunk/ |
| 108 |
Scripts updates to correct paths when working under Windows. Now, ModelSim, Xilinx and Altera synthesis are working on Windows through batch files.
Icarus Verilog and Altera synthesis are working as well. Job done! |
rfajardo |
4559d 09h |
/minsoc/trunk/ |
| 107 |
Adding setup batch script for Altera synthesis on Windows.
prj/scripts/altprj.sh has now to check if it is run from cygwin in order to re-formulate the path to windows system.
Maybe the other scripts have to be updated too. This will be checked soon. |
rfajardo |
4559d 12h |
/minsoc/trunk/ |
| 106 |
Installation script was checking the ENV variable before setting it. |
rfajardo |
4559d 15h |
/minsoc/trunk/ |
| 105 |
Updating configure scripts to copy Windows synthesis launch script setup.bat from either minsoc/syn/altera or minsoc/syn/xilinx to minsoc/syn. |
rfajardo |
4559d 17h |
/minsoc/trunk/ |
| 104 |
Enabling modelsim simulation for current project definition.
vhdl and verilog projects have to be separated:
-prj/Makefile defines VHDL_PROJECTS and VERILOG_PROJECTS, they are merged into PROJECTS. Tools which don't care about VHDL or Verilog use PROJECTS list while other tools use VERILOG_ or VHDL_PROJECTS.
-Simulation uses VHDL_PROJECTS and VERILOG_PROJECTS independently.
-prj/scripts/simprj.sh splitted in:
-simvhdl.sh
-simverilog.sh
(they generate the input files in the right format for simulation tools) |
rfajardo |
4566d 15h |
/minsoc/trunk/ |
| 103 |
But the file is called gdb-6.8a.tar.bz2, so tar must be run on that name. |
rfajardo |
4569d 06h |
/minsoc/trunk/ |
| 102 |
GNU GDB FTP has renamed gdb-6.8 package to gdb-6.8a package. Uncompressed it remains gdb-6.8, so no other changes to script are necessary. |
rfajardo |
4569d 06h |
/minsoc/trunk/ |
| 101 |
Documentation, wiki's address updated. |
rfajardo |
4594d 18h |
/minsoc/trunk/ |
