| Rev |
Log message |
Author |
Age |
Path |
| 165 |
Board contribution: nexys2_1200 (Thanks to Johan Granath)
spartan3e_starter_kit_eth/minsoc_bench_defines.v: deprecated definition updated |
rfajardo |
4000d 05h |
/minsoc/trunk/ |
| 164 |
Updating width of minsoc_tc_top.v for Wishbone B3 compliance. This file has never worked. This solves at least the bug that some signals were not being routed through. |
rfajardo |
4064d 22h |
/minsoc/trunk/ |
| 163 |
Adjusting internal initiator array widths. They were 1 bit too large. Thanks to R. Diez report.
These arrays abstract the complete initiator inputs. This way it is easier to route and arbiter using a single input.
Also removing 2 sequential delays. I didn't design them, so I can't tell if they were really useful/good. |
rfajardo |
4071d 05h |
/minsoc/trunk/ |
| 162 |
Tasks don't have parenthesis. This is only used for ports on modules. This was a mistake from my part. |
rfajardo |
4076d 23h |
/minsoc/trunk/ |
| 161 |
Correcting configure parameters of adv_jtag_bridge on installation script. |
rfajardo |
4090d 02h |
/minsoc/trunk/ |
| 160 |
Typo in minsoc-install.sh script. Adv_jtag_bridge was not configuring correctly. |
rfajardo |
4090d 03h |
/minsoc/trunk/ |
| 159 |
Updated constraint file for de2_115 board. (Richard Hasha) |
rfajardo |
4090d 03h |
/minsoc/trunk/ |
| 158 |
Adding de2_115_board port, thanks to Richard Hasha.
Support to JSP (JTAG Serial Port) working well. Also provided by Richard Hasha.
Different interconnect configurations per board are not straightforward on MinSoC. New added modules or definitions for addresses have to be carried over to other boards. Furthermore, extra modules can be shared among all projects. Thus, it is better to have this centralized:
-Removing interconnect configuration from minsoc_defines.v. There is an interconnect_defines.v file on rtl/verilog. The software counterpart is interconnect.h on sw/drivers.
Including a jsp firmware. It is basically the uart firmware but using JSP instead. Added to all board configure scripts to be compiled on configuration.
prj/srcs extended to include jsp and interconnec_defines.v.
spartan3e_starter_kit_eth lost UART (does not fit) and uses JSP instead now. |
rfajardo |
4091d 19h |
/minsoc/trunk/ |
| 157 |
Removed obsolete file; the changes in this version have been merged into
the mainline advanced debug system version 3.0 and higher. |
nyawn |
4097d 14h |
/minsoc/trunk/ |
| 156 |
Added hardware watchpoint indicators to debug unit break input, to allow
the debugger to break when a hardware watchpoint is triggered. |
nyawn |
4097d 14h |
/minsoc/trunk/ |
| 155 |
Decreased wait time, for faster simulations. |
nyawn |
4097d 14h |
/minsoc/trunk/ |
| 154 |
Modified to use the new autotools support in the advanced debug system v3.0. |
nyawn |
4097d 14h |
/minsoc/trunk/ |
| 149 |
Merging differences of release candidate 1.0 revision 140:148 with trunk. |
rfajardo |
4130d 05h |
/minsoc/trunk/ |
| 144 |
Updating configure scripts. Calling make into the right directories now. |
rfajardo |
4136d 04h |
/minsoc/trunk/ |
| 142 |
Updating configure.sh:
1) we don't patch the trunk version.
2) it is better to re-compile the firmwares on reconfiguration. So compiling firmwares went to configure scripts instead.
backend/xxx/configure: compiling firmwares here now. |
rfajardo |
4136d 04h |
/minsoc/trunk/ |
| 141 |
Merging with rc-1.0 revision 140. I doubt rc-1.0 will still change much in the last days. |
rfajardo |
4136d 04h |
/minsoc/trunk/ |
| 135 |
Installation on Ubuntu-11.10 has shown that package texinfo is required to compiled GDB. This package installs the binary makeinfo. |
rfajardo |
4143d 23h |
/minsoc/trunk/ |
| 108 |
Scripts updates to correct paths when working under Windows. Now, ModelSim, Xilinx and Altera synthesis are working on Windows through batch files.
Icarus Verilog and Altera synthesis are working as well. Job done! |
rfajardo |
4162d 22h |
/minsoc/trunk/ |
| 107 |
Adding setup batch script for Altera synthesis on Windows.
prj/scripts/altprj.sh has now to check if it is run from cygwin in order to re-formulate the path to windows system.
Maybe the other scripts have to be updated too. This will be checked soon. |
rfajardo |
4163d 01h |
/minsoc/trunk/ |
| 106 |
Installation script was checking the ENV variable before setting it. |
rfajardo |
4163d 04h |
/minsoc/trunk/ |
| 105 |
Updating configure scripts to copy Windows synthesis launch script setup.bat from either minsoc/syn/altera or minsoc/syn/xilinx to minsoc/syn. |
rfajardo |
4163d 06h |
/minsoc/trunk/ |
| 104 |
Enabling modelsim simulation for current project definition.
vhdl and verilog projects have to be separated:
-prj/Makefile defines VHDL_PROJECTS and VERILOG_PROJECTS, they are merged into PROJECTS. Tools which don't care about VHDL or Verilog use PROJECTS list while other tools use VERILOG_ or VHDL_PROJECTS.
-Simulation uses VHDL_PROJECTS and VERILOG_PROJECTS independently.
-prj/scripts/simprj.sh splitted in:
-simvhdl.sh
-simverilog.sh
(they generate the input files in the right format for simulation tools) |
rfajardo |
4170d 04h |
/minsoc/trunk/ |
| 103 |
But the file is called gdb-6.8a.tar.bz2, so tar must be run on that name. |
rfajardo |
4172d 19h |
/minsoc/trunk/ |
| 102 |
GNU GDB FTP has renamed gdb-6.8 package to gdb-6.8a package. Uncompressed it remains gdb-6.8, so no other changes to script are necessary. |
rfajardo |
4172d 19h |
/minsoc/trunk/ |
| 101 |
Documentation, wiki's address updated. |
rfajardo |
4198d 07h |
/minsoc/trunk/ |
| 100 |
syn/altera/minsoc_top.qsf: I thought this file was being generated now as project file description. But it is merely a synthesis configuration file and must be here. File re-added. |
rfajardo |
4207d 05h |
/minsoc/trunk/ |
| 99 |
backend/altera_3c25_board/minsoc_defines.v: if GENERIC_FPGA selected, undefine ALTERA_FPGA and FPGA_FAMILY to avoid vendor specific code to flow into the simulation. If you don't do it, generate_bench fails. |
rfajardo |
4207d 05h |
/minsoc/trunk/ |
| 98 |
Removing deprecated minsoc_top.qsf file. |
rfajardo |
4207d 06h |
/minsoc/trunk/ |
| 97 |
As proposed by Javier Almansa automatically generated project files for simulation and synthesis are out of revision control. Instead, the backend configure scripts run the prj/Makefile now to generate the project files prior to configuration of SoC for a specific board. |
rfajardo |
4207d 06h |
/minsoc/trunk/ |
| 96 |
Some files needed for Altera synthesis |
javieralso |
4207d 17h |
/minsoc/trunk/ |
