Rev |
Log message |
Author |
Age |
Path |
158 |
Adding de2_115_board port, thanks to Richard Hasha.
Support to JSP (JTAG Serial Port) working well. Also provided by Richard Hasha.
Different interconnect configurations per board are not straightforward on MinSoC. New added modules or definitions for addresses have to be carried over to other boards. Furthermore, extra modules can be shared among all projects. Thus, it is better to have this centralized:
-Removing interconnect configuration from minsoc_defines.v. There is an interconnect_defines.v file on rtl/verilog. The software counterpart is interconnect.h on sw/drivers.
Including a jsp firmware. It is basically the uart firmware but using JSP instead. Added to all board configure scripts to be compiled on configuration.
prj/srcs extended to include jsp and interconnec_defines.v.
spartan3e_starter_kit_eth lost UART (does not fit) and uses JSP instead now. |
rfajardo |
4170d 16h |
/minsoc/trunk/utils/ |
157 |
Removed obsolete file; the changes in this version have been merged into
the mainline advanced debug system version 3.0 and higher. |
nyawn |
4176d 11h |
/minsoc/trunk/utils/ |
154 |
Modified to use the new autotools support in the advanced debug system v3.0. |
nyawn |
4176d 11h |
/minsoc/trunk/utils/ |
149 |
Merging differences of release candidate 1.0 revision 140:148 with trunk. |
rfajardo |
4209d 01h |
/minsoc/trunk/utils/ |
142 |
Updating configure.sh:
1) we don't patch the trunk version.
2) it is better to re-compile the firmwares on reconfiguration. So compiling firmwares went to configure scripts instead.
backend/xxx/configure: compiling firmwares here now. |
rfajardo |
4215d 00h |
/minsoc/trunk/utils/ |
141 |
Merging with rc-1.0 revision 140. I doubt rc-1.0 will still change much in the last days. |
rfajardo |
4215d 01h |
/minsoc/trunk/utils/ |
135 |
Installation on Ubuntu-11.10 has shown that package texinfo is required to compiled GDB. This package installs the binary makeinfo. |
rfajardo |
4222d 20h |
/minsoc/trunk/utils/ |
106 |
Installation script was checking the ENV variable before setting it. |
rfajardo |
4242d 00h |
/minsoc/trunk/utils/ |
103 |
But the file is called gdb-6.8a.tar.bz2, so tar must be run on that name. |
rfajardo |
4251d 16h |
/minsoc/trunk/utils/ |
102 |
GNU GDB FTP has renamed gdb-6.8 package to gdb-6.8a package. Uncompressed it remains gdb-6.8, so no other changes to script are necessary. |
rfajardo |
4251d 16h |
/minsoc/trunk/utils/ |
83 |
minsoc-install.sh: bzip2 program was being used, but its existance on target system was not being verified. It is now. |
rfajardo |
4304d 02h |
/minsoc/trunk/utils/ |
82 |
minsoc-install.sh: problems with copying the GNU Toolchain from download to tools. We uncompress the GNU Toolchain now once again to tools during the installation part. |
rfajardo |
4307d 01h |
/minsoc/trunk/utils/ |
81 |
Installation script complete, nice text feedback, output logs and better execution order. |
rfajardo |
4307d 12h |
/minsoc/trunk/utils/ |
79 |
minsoc-install.sh: rpath corrected.
required-cygwin-tools: updated |
rfajardo |
4310d 17h |
/minsoc/trunk/utils/ |
78 |
minsoc-install.sh: Advanced JTAG bridge compilation needs to know where the dynamic libraries are on runtime. Patching (sed) the Makefile to compile it with the rpath to the libraries (libusb/libftdi). |
rfajardo |
4310d 17h |
/minsoc/trunk/utils/ |
77 |
New tool requirements for installing Icarus Verilog. |
rfajardo |
4310d 18h |
/minsoc/trunk/utils/ |
76 |
Including a script allowing the installation of MinSoC and all its required tools.
It should be working for all Linuxes and Cygwin. |
rfajardo |
4310d 18h |
/minsoc/trunk/utils/ |
64 |
firmware makefiles:
-every firmware makefile has now complete dependency. This also includes dependency on files under minsoc/backend (target specific files). That means, that if some target specific header changes, the support library dependent on it will be compiled. That will always happen, even if you compile the uart firmware. In other words, if you want to use uart firmware, you can always simply compile uart by issuing make all. If anything has changed, backend files, support library, drivers, it will update everything for you.
-TODO: dependency can be automatic created by using make together with gcc. Use it instead of declaring all dependencies manually.
Makefile system for synthesis:
-the dependency for every implementation step has been checked and is working fine.
-Makefile plus support files have been moved to minsoc/syn/src
-make usage is still under syn through files generated by backend bashscripts
Backend:
-files under backend are target specific files used for the system to work
-firmware compilation
-system simulation
-system implementation
-This directory is populated by visiting one of its subdirectories and typing ./configure
backend/spartan3a_dsp_kit:
-working on FPGA
backend/spartan3e_starter_kit:
-has to be tested
backend/ml509:
-missing files have to be copied and adapted, configure script has to be copied and adapted
backend/std:
-include files necessary for firmware compilation and system configuration
-it does not include files for synthesis and is not synthesizable |
rfajardo |
4418d 00h |
/minsoc/trunk/utils/ |
47 |
Firmware updated to work with gcc-4.5. It is actually working just fine and gcc-4.5 assembly code seems a lot cleaner.
I noticed that by increasing the free stack space for the interrupt handler by 130 made the resulting firmware not work. I assume it is because 130 is not aligned 130%4 = 2 and the stack simply does not work then. Instead I'm freeing the previous 116 plus 128 (for 32 registers as mentioned by Jeremy) and it works. |
rfajardo |
4460d 21h |
/minsoc/trunk/utils/ |
46 |
Including an explanation of what has to be updated on gpio to port it smoothly to minsoc. |
rfajardo |
4461d 01h |
/minsoc/trunk/utils/ |