OpenCores
URL https://opencores.org/ocsvn/minsoc/minsoc/trunk

Subversion Repositories minsoc

[/] - Rev 153

Rev

Go to most recent revision

Filtering Options

Clear current filter

Rev Log message Author Age Path
153 Updating installation script to download minsoc from this branche, verilator, instead of rc-1.0. rfajardo 2930d 04h /
152 Roll back to retrieve minsoc from branches/rc-1.0. rfajardo 2930d 05h /
151 Creating tag release-1.0 from revision 150 of branches/rc-1.0. rfajardo 2930d 05h /
150 Updating installation script to retrieve minsoc from tags/release-1.0. rfajardo 2930d 05h /
149 Merging differences of release candidate 1.0 revision 140:148 with trunk. rfajardo 2930d 05h /
148 Renaming minsoc_wave.lxt to minsoc_wave.lxt2 for correctness. rfajardo 2935d 01h /
147 Updating minsoc_bench.v to correctly acquire uart data.

Uart drivers: when an end of line character was sent, the driver appended a carriage return to it. This is not necessary and has been removed.
-Eth and Uart firmwares also had a carriage return after the end of line, also removed.

Minsoc_bench_defines.v: Renaming VCD_OUTPUT define to WAVEFORM_OUTPUT

run_bench: selecting -lxt2 for waveform output format. This output format size is 10 times smaller than vcd.

minsoc-install.sh: lxt2 output format requires that Icarus Verilog be installed with zlib support. For that, we now check if zlib is supported on script run.
rfajardo 2935d 03h /
146 Importing 'Xilinx Microblaze Dev. Kit 1600E Edition' board configuration directory. ConX. 2935d 09h /
145 minsoc_bench_core.v and minsoc_bench_clock.v left only on verilator branche. It will develop there until it is ported for inclusion into trunk. RC-1.0 is now clean of it. rfajardo 2935d 18h /
144 Updating configure scripts. Calling make into the right directories now. rfajardo 2936d 04h /
143 Compiling firmwares in board configuration scripts instead of on global minsoc setup. rfajardo 2936d 04h /
142 Updating configure.sh:
1) we don't patch the trunk version.
2) it is better to re-compile the firmwares on reconfiguration. So compiling firmwares went to configure scripts instead.

backend/xxx/configure: compiling firmwares here now.
rfajardo 2936d 05h /
141 Merging with rc-1.0 revision 140. I doubt rc-1.0 will still change much in the last days. rfajardo 2936d 05h /
140 Including required modules for verilator simulation. rfajardo 2936d 05h /
139 Creating a verilator branche. rfajardo 2936d 05h /
138 DIR_TO_INSTALL creation using wizard ConX. 2936d 18h /
137 Removing uncomplete support for ml509 and not working support for spartan3e_starter_kit_eth (area constraint cannot be reached). rfajardo 2937d 05h /
136 Installation on Ubuntu-11.10 has shown that a binary called makeinfo is required to install GDB. This binary can be installed on Ubuntu by installing the package texinfo. rfajardo 2944d 00h /
135 Installation on Ubuntu-11.10 has shown that package texinfo is required to compiled GDB. This package installs the binary makeinfo. rfajardo 2944d 00h /
134 run_sim.bat for ModelSim updated to acquire the firmware_size for command line input when running the testbench. rfajardo 2951d 04h /

1 2 Next >

Show All

powered by: WebSVN 2.1.0

© copyright 1999-2019 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.