| Rev |
Log message |
Author |
Age |
Path |
| 223 |
Added an OPEN8_BUS_TYPE record to simplify connection to Open8 modules. The CPU now passes and Open8_Bus out, which supplies the bus address, write enable, write data, and read enable. Read data and interrupts are still handled as separate signals, since they are muxed/connected at the next level up. |
jshamlet |
1506d 14h |
/open8_urisc/trunk/VHDL/o8_cpu.vhd |
| 210 |
Modified the timers to reset on new interval write. This avoids an issue in the original design where the timer had to reach zero before updating, potentially causing unwanted interrupts.
Also added a flag to the CPU to allow interrupts to be processed sequentially based on the state of the I bit. This one is set to false by default, as it is a significant change in interrupt behavior. Long, and reentrant, ISRs can clear the I bit prematurely to allow themselves to be interrupted.
Lastly, added the I bit to the exported flags for possible use in memory protection schemes. |
jshamlet |
1512d 22h |
/open8_urisc/trunk/VHDL/o8_cpu.vhd |
| 209 |
Fixed an issue in the PIT timer that caused an immediate interrupt on interval write,
Fixed an issue in the epoch timer that resulted in a spurious interrupt due to extra LSB's being set by default in the set point register,
While cleaning elsewhere, founding a spacing issue in the CPU HDL,
Added a 4k ROM and MW core. |
jshamlet |
1513d 11h |
/open8_urisc/trunk/VHDL/o8_cpu.vhd |
| 194 |
Cleaned up licensing sections |
jshamlet |
1521d 17h |
/open8_urisc/trunk/VHDL/o8_cpu.vhd |
| 191 |
Cleaned up comments, added back the OPEN8_NULLBUS constant, and added some new modules for ADCs and LCD displays.
Also made the button input module more configurable by moving the debounce code to a separate entity and using generics to instantiate it. |
jshamlet |
1521d 17h |
/open8_urisc/trunk/VHDL/o8_cpu.vhd |
| 190 |
Fixed a bug in CPU where RTI/RTS wasn't idling the instruction cache, causing intermittent failures where RTI would execute as RTS, corrupting the stack;
Fixed a bug in the real-time clock where the uSec tick generator would stop if the PIT timer value was left/set to 0x00. |
jshamlet |
1533d 15h |
/open8_urisc/trunk/VHDL/o8_cpu.vhd |
| 188 |
Added a generic to alter the behavior of RTI so that it can optionally skip restoring the general purpose flags GP4 to GP7, allowing ISR's to make persistent changes to them. Also exported these flags to the top level for use outside the CPU. |
jshamlet |
1534d 18h |
/open8_urisc/trunk/VHDL/o8_cpu.vhd |
| 187 |
Added the CPU_Halt input, only now as an input to the instruction decoder. The CPU_Halt line will assert the registered CPU_Halt_Req, which will cause the instruction decoder to abort the current instruction, reset the PC, then enter a hold state until the line is deasserted. Additionally, a very minor bug that could cause the SMSK instruction to effectively execute twice if interrupted was fixed. Lastly, cleaned up the comments even more. |
jshamlet |
1536d 15h |
/open8_urisc/trunk/VHDL/o8_cpu.vhd |
| 186 |
Merged the interrupt override logic into the case structure, simplifying how interrupts are processed. |
jshamlet |
1539d 14h |
/open8_urisc/trunk/VHDL/o8_cpu.vhd |
| 185 |
1) Fixed an apparently long-standing bug where the interrupt bit wasn't being cleared after an RTI
2) Modified the program counter logic to be simpler. It now always increments, and states control the increment using the offset field. A new set of constants was added to replace the old states.
3) Modified the ALU to always use Operand1 instead of ALU_Ctrl.Data (and removed the field in the record). A new ALU command, ALU_GMSK, was added, as it was the only instruction to set the .Data field to something other than Operand1 (Int_Mask)
4) Modified the package file so that flag names match what the assembler calls them. FL_Z is now PSR_Z, FL_GP1 is now PSR_GP4, etc.
5) Cleaned up the comments and code formatting |
jshamlet |
1539d 17h |
/open8_urisc/trunk/VHDL/o8_cpu.vhd |
