Subversion Repositories qspiflash

[/] [qspiflash/] [trunk/] [rtl/] - Rev 23


Filtering Options

Clear current filter

Rev Log message Author Age Path
23 Updated headers dgisselq 604d 07h /qspiflash/trunk/rtl/
22 Read only is now an option of wbqspiflash

It was a macro before.
dgisselq 604d 07h /qspiflash/trunk/rtl/
20 Changed reference to flash_config to flashconfig.v dgisselq 1077d 20h /qspiflash/trunk/rtl/
19 LLQSPI now passes formal tests dgisselq 1077d 20h /qspiflash/trunk/rtl/
18 Renamed the flash config file dgisselq 1077d 20h /qspiflash/trunk/rtl/
16 Added a full blown test bench to the controller

This includes:
- A global make file, and a "make test" which will build the test bench.
- Merging other versions of the QSPI flash driver I had lying around
- Grabbing the best of these, and verifying that they work
- The result is a reduction in overall logic
dgisselq 1220d 01h /qspiflash/trunk/rtl/
14 Updates: little-big endian, various other fixes

1. Made the wbqspiflash.v and llqspi.v files compile with default_nettype none
2. Changed the internal flash representation to big endian. A little-big
endian conversion is now required when writing to the flash from a PC.
3. Simplified the address description via w_wb_addr and w_spif_addr, so that
the core is more flexible when changing sizes.
4. Removed the dependence upon the WB_CYC line ... as part of the WB
simplifications I've been doing.
5. Got XIP working for the EQSPI flash (I guess --- it's been a while since
I made those changes)
6. Adjusted (fixed) sim of read/writes to the volatile config register
(necessary for XIP)
dgisselq 1241d 07h /qspiflash/trunk/rtl/
11 This code has been proven, and is currently working within an Arty platform. dgisselq 1510d 22h /qspiflash/trunk/rtl/
10 Switched to Quad Output mode by default. dgisselq 1527d 20h /qspiflash/trunk/rtl/
9 Minor changes to the baseline, FIRST RELEASE OF THE EQSPIFLASH controller!! dgisselq 1527d 22h /qspiflash/trunk/rtl/
8 Minor documentation edits. dgisselq 1758d 19h /qspiflash/trunk/rtl/
7 Added the ability to make the Quad/SPI flash run in read-only mode, in an
effort to reduce it's resource/LUT usage enough to run on a Digilent Cmod-S6.
dgisselq 1779d 04h /qspiflash/trunk/rtl/
4 FIXED: in the previous version, the first read of the device would always fail.
This was due to the fact that the Xilinx loader that read from the device
to load the Xilinx configuration left the Quad SPI flash chip in a high
data rate state. Thus, on reset, the first thing this core does it to
take the device out of the high data rate state.

Also, on a bus action waiting on a write to complete, the timing was
off. This has now been corrected. Reads (in both modes) should now
stall the bus (properly) while a write/erase cycle is ongoing, and
complete when finished.

The bug in high speed writing was traced to a read bug, not a write bug.
High speed (i.e. 4-bit transaction) writing has been re-enabled.

The bug in transitioning from 1-bit mode to 4-bit reads has been fixed.
This was causing the high speed write bug mentioned above.

Read ID was stalling the bus. This was traced to a sign error while
referencing the chip select line, and has been fixed.

The lowerlevel QSPI project was modified to add a holding state. We were
struggling with a bug whereby a late read would hang the device. The upper
level driver would issue it when the lower level driver was busy, and yet
think that it was accomplished. The lower level driver was moving from ready
to idle, so it never saw the read. Now, hold keeps the lower level driver
in the ready state at the end of a read until the bus transaction is complete,
or until it goes on to some other transaction other than reading data.
(This was a big change.)

Finally, unnecessary debugging lines were disabled in the simulator.
dgisselq 1959d 02h /qspiflash/trunk/rtl/
3 This quick update fixes some oopses associated with the original release.
Specifically, I made sure the license comments were available in all source
files, made sure all source files mentioned that they were a part of a Quad
SPI flash controller, rather than the Basys-3 development board project they
were originally a part of or the Spartan 3E project before that, I took out
the (undocumented) debug "scaffolding" that was still in the Verilog files,
and I added the C++ source for the bench test/simulator into the project.
Although the full bench test is not complete, it should be sufficient for
anyone who would wish to test this within Verilator.

These changes should not affect any of the functionality of the core.
dgisselq 1965d 18h /qspiflash/trunk/rtl/
2 Initial submission. dgisselq 1965d 20h /qspiflash/trunk/rtl/

powered by: WebSVN 2.1.0

© copyright 1999-2020, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.