| Rev |
Log message |
Author |
Age |
Path |
| 93 |
Oops -- missed adjusting the copyright. |
dgisselq |
2896d 02h |
/xulalx25soc/trunk/sw/ |
| 92 |
Fixes the problem whereby the master counters show when the user counters should
be showing and vice versa. Now the master counters show by default, together
with their correct labels. User counters are still available by pressing
'u' in the debugger, and the master counter display may be returned to by
pressing 'm' in the debugger. |
dgisselq |
2896d 02h |
/xulalx25soc/trunk/sw/ |
| 91 |
Fixes bugs associated with an overflow of write acknowledgements in the
receiver. This helps keep our accesses aligned. |
dgisselq |
2896d 02h |
/xulalx25soc/trunk/sw/ |
| 78 |
Comments out the line that caused a compiler warning--setting an unused
variable. Code should be better as a result. |
dgisselq |
2901d 22h |
/xulalx25soc/trunk/sw/ |
| 77 |
Adds register names and values for the SD card interface. |
dgisselq |
2901d 22h |
/xulalx25soc/trunk/sw/ |
| 76 |
Now tries to avoid reading from the stack if the stack addresses are already
known to be bad. That way, the debugger tries to preserve any bus error address
already on the buserr device. |
dgisselq |
2901d 22h |
/xulalx25soc/trunk/sw/ |
| 53 |
Added a touch of error checking. |
dgisselq |
2949d 23h |
/xulalx25soc/trunk/sw/ |
| 49 |
Added some documentation to make the read and write calls easier to understand. |
dgisselq |
2978d 00h |
/xulalx25soc/trunk/sw/ |
| 46 |
This is a bug fix release--fixing the bug that kept dumpsdram.cpp/wbsdram.v
from working when long pipelined reads were interrupted by the necessity of
a pair of refresh cycles. |
dgisselq |
2980d 02h |
/xulalx25soc/trunk/sw/ |
| 42 |
Minor changes. |
dgisselq |
2983d 22h |
/xulalx25soc/trunk/sw/ |
| 41 |
Bug fix. This was preventing dumpsdram from accurately reading back what
had been written to the RAM earlier. |
dgisselq |
2983d 22h |
/xulalx25soc/trunk/sw/ |
| 40 |
This adds to dumpsdram the capability to run over a port, such as with
busmaster_tb. |
dgisselq |
2985d 09h |
/xulalx25soc/trunk/sw/ |
| 38 |
Updated to remove the build dependence upon ZipCPU. |
dgisselq |
2987d 08h |
/xulalx25soc/trunk/sw/ |
| 33 |
Oops -- the audio was wired audio first then the interrupt controller, not
the other way around. This adjusts regdefs to match what's on the chip. |
dgisselq |
2992d 00h |
/xulalx25soc/trunk/sw/ |
| 31 |
A bug fix, although one that rearranges the bus. The first four I/O locations
have been adjusted. The new locations are reflected in wishbone.html. In
addition, the PWM and UART devices no longer create bus errors when accessed.
Finally, this version uses a `define XULA25 to determine whether or not to build
for the XuLA2-LX9 or the XuLA2-LX25. If defined, it will build for the
XuLA2-LX25. If not, for the XuLA2-LX9. The ideal location for this define
would be to place it into your Xilinx configuration, should you wish to build
for the LX25. |
dgisselq |
2992d 01h |
/xulalx25soc/trunk/sw/ |
| 30 |
Bug fixes. In particular, this fixes a segmentation violation. |
dgisselq |
2992d 05h |
/xulalx25soc/trunk/sw/ |
| 29 |
This adds a vastly updated and superious ziprun capability to the repository.
ziprun now accepts ELF program files *only*, reads them, and places them onto
the board. This includes the ability, within the ELF file, of specifying
whether or not the data is sent to block ram, SD ram, or Flash, as well as
the ability of specifying the initial address. (Of course, that's a one time
thing--to always have the same initial address, set the address in
rtl/busmaster.v) |
dgisselq |
2992d 21h |
/xulalx25soc/trunk/sw/ |
| 28 |
Oops--two files needed by zipdbg weren't originally placed in the directory. |
dgisselq |
2993d 01h |
/xulalx25soc/trunk/sw/ |
| 25 |
Fixing compile time warnings. |
dgisselq |
2993d 02h |
/xulalx25soc/trunk/sw/ |
| 24 |
Added the #define necessary to enable (and clear) SCOPE interrupts. |
dgisselq |
2999d 00h |
/xulalx25soc/trunk/sw/ |
| 17 |
Some basic updates, to include adding in a missing file (zipstate). Most of
these updates include making sure that the XuLA2 device can be accessed via
the USB. (Prior versions accessed the FPGA via serial port or network ...) |
dgisselq |
3058d 01h |
/xulalx25soc/trunk/sw/ |
| 13 |
This version is now working. (It probably would've worked before, but
everything is now working.) |
dgisselq |
3059d 21h |
/xulalx25soc/trunk/sw/ |
| 11 |
Getting software up and running on the board for the first time. (Not there
yet, but I think these items have now proven themselves.) |
dgisselq |
3060d 00h |
/xulalx25soc/trunk/sw/ |
| 7 |
Mostly minor changes. Fixed the legal copyright statement in the UART files,
adjusted some comments, and made sure that the zipdbg program contained all
the latest features from our Vault. |
dgisselq |
3062d 10h |
/xulalx25soc/trunk/sw/ |
| 5 |
Initial software version, in support of the project. At this point, they are
provided with no guarantees that they work. (They did use to work--on an older
build, but I haven't been able to verify that they work with this newer build
yet.) |
dgisselq |
3062d 20h |
/xulalx25soc/trunk/sw/ |
