Rev |
Log message |
Author |
Age |
Path |
99 |
Added big-endian versus little-endian functionality. You can now specify which
your input file is as a command line parameter, and zdump will properly
disassemble the file. |
dgisselq |
3122d 07h |
/ |
98 |
Added justed longjump instructions from the previous (not used, broken)
functionality to the new LOD (PC),PC functionality. |
dgisselq |
3122d 07h |
/ |
97 |
Added longjump instructions. |
dgisselq |
3122d 07h |
/ |
96 |
Added the longjump functionality, so that the assembler will properly assemble
instructions to arbitrary 32-bit addresses. |
dgisselq |
3122d 07h |
/ |
95 |
Fixed a bug whereby a mistaken code for CLR was masking a valid LDI of a large
integer value. |
dgisselq |
3124d 13h |
/ |
94 |
These changes make it possible to build binutils-2.25/ here in this
directory. "make binutils" should be all that is necessary to build the
entire binutils package for the Zip CPU.
The default configure script, run from gas-script.sh below, will build and
install these utilities in an install/ subdirectory made below sw/. |
dgisselq |
3149d 10h |
/ |
93 |
A BINUTILS BACKEND IS NOW AVAILABLE!!!! |
dgisselq |
3157d 08h |
/ |
92 |
Adjustments made to match the simplified early branching. |
dgisselq |
3157d 08h |
/ |
91 |
Minor updates. |
dgisselq |
3157d 08h |
/ |
90 |
Removed MOV x(PC),PC from the list of possible early branching instructions.
ADD X,PC and LDI X,PC are now the only recognized early branching instructions.
This was done to spare logic, although I don't think I spared more than a
LUT or two. |
dgisselq |
3157d 08h |
/ |
89 |
Minor changes, to include making default branching an ADD.[condition] X,PC
instruction, rather than allowing both MOV X(PC),PC and ADD X,PC instructions.
Further zopcodes.cpp contains several bug fixes. |
dgisselq |
3157d 08h |
/ |
88 |
Eliminated some warnings. The div fixes were to simplify the logic, even though
the result is less readable ... |
dgisselq |
3181d 08h |
/ |
87 |
Adjusted the operator input line to reflect actual logic inputs, rather
than the registered inputs which may have been out of date. (Indeed, they
were out of date for the bug I was chasing and fixed ...) |
dgisselq |
3183d 06h |
/ |
86 |
Removed the requirement to have the dev.scope.cpu hardware defined outside
of the Zip CPU (it was defined in another project). This was causing a bus
error in the simulator (which it should have), but taking it out fixes things
in the simulator (while removing capability from one special piece of H/W). |
dgisselq |
3183d 07h |
/ |
85 |
Minor update/correction to operand B definition. |
dgisselq |
3183d 07h |
/ |
84 |
Minor updates. |
dgisselq |
3183d 07h |
/ |
83 |
Added a flag to indicate whether an exception took place on the first
or second half of a VLIW instruction--will be zero in non-VLIW mode,
equivalent to the second half of the instruction having caused the
exception. (Expect these flags to be reordered some time in the future into
a less haphazard ordering ...)
Vastly simplified the pipeline logic, primarily for op_stall, but also touched
opA and opB. (Trying to fit within timing on Spartan 6 ...)
Changed division instruction to include a reset on clear_pipeline, to make
certain [BC $addr; DIV Rx,Ry ] works regardless of whether the condition is
true. |
dgisselq |
3183d 07h |
/ |
82 |
Found and (I hope) fixed a nasty bug that would send the prefetch into an
endless loop whenever you jumped to an instruction at the last location
in an unloaded cache line. |
dgisselq |
3183d 07h |
/ |
81 |
Trying to clean up ISE generated warnings. |
dgisselq |
3183d 07h |
/ |
80 |
Bug fix: declared the (combined) multiply to be signed again. Also
changed the name of the generate'd for block, to keep ISE from complaining. |
dgisselq |
3183d 07h |
/ |
79 |
Adjusted the opcodes for NOOP, BREAK, and LOCK. |
dgisselq |
3187d 11h |
/ |
78 |
Found/corrected annoying bug in floating point documentation of the opcode
table. |
dgisselq |
3187d 11h |
/ |
77 |
First check-in: the test bench for the divide instruction. |
dgisselq |
3188d 10h |
/ |
76 |
The biggest change here was to zippy_tb, to make it more similar to the debugger
and to make it work with VLIW-type instructions. |
dgisselq |
3188d 10h |
/ |
75 |
Modified for VLIW instructions. |
dgisselq |
3188d 10h |
/ |
74 |
Added a bunch of debugging code to the Dhrystone benchmark assembly file, as
well as two new testing assembly files. |
dgisselq |
3188d 10h |
/ |
73 |
Documentations updates. |
dgisselq |
3188d 10h |
/ |
72 |
Some updated graphics, now containing images of the CPU that include the
divide and (currently non-existant) floating point unit. |
dgisselq |
3188d 10h |
/ |
71 |
This contains a bunch of bug fixes. (A lot ...) For example, the pipeline
stall code has also seriously changed, to fixed the pipeline memory load/op
stage conflict, while maintaining no-stall operation for operands that don't
need an offset. This had a cascading effect, however, so that the multiply
could no longer complete in a single cycle. Therefore, the timing on the
multiplies was slowed down to two cycles from a single cycle. (It's the
only two-cycle ALU operation ...) The illegal instruction code has also been
fixed, so that illegal instructions no longer stalls the prefetch bus. |
dgisselq |
3188d 10h |
/ |
70 |
Updated the assembler support files, zopcodes in particular, to handle
the disassembly of the new very long instruction word codes. |
dgisselq |
3188d 10h |
/ |